Land Warrior Airsoft - Airsoft Equipment Specialists

This is a 7mm steel spring guide with zinc coating providing maximum durability.

Suitable for APS type rifles.

Spring guide has no hole, which is riquired for some guns.

Guide will fit L96 Type 96 Rifles i.e. Well, Warrior and can be used with the stock springs and pistons if you do not require the use of the firing pin (remove f. pin).

Will also fit M99, M24 made by Snow Wolf and the Well MB-06.

Aluminium body and stainless steel piston end.

Can be used with both 9mm and 11mm springs.

Suitable for:
Well MB01 (Warrior L96)
Well MB04
Well MB05
Well MB06
Well MB08
Maruzen Type 96
SW (Snow Wolf) M24 / M99

One Piece Aluminium high pressure piston for the L96.

Suitable for the most spring airsoft guns based on APS system. It means APS 2, EX a Type96 and china made copies Well MB-01,04,05,06,08, L96 Warrior, SW M24 and SW M99.

Cannot be used for MP001, VSR,MB03, AGM 002 or BAR10.

Suitable with springs upto 600 fps tested for durability purposes only.

Suitable for Warrior, Well, Mauser versions 1 & 2. Will also fit Snow Wolf M99 and M24 with modification (will need pot metal o-ring, see below).You will still need to change the hop bucking.

L96 v3 Owners (the model with a velocity reducer) will need new cylinder head, see below.

Note - For experienced modders/upgraders.
A high precision replacement hop-up unit based on the Hexagon design. Full metal construction for better durability. Hop up unit designed for Well MB-01 series, compatible with G21 and G22 series, MB-04, 05 and Barett M99 Snow Wolf.

Designed to use with TM compatible Hop up bucking and AEG Inner barrel. O-ring sealed front and rear, for maximum air-seal. "Pot Metal Ring" from the original Hop up unit is needed for installation.

This will also fit the Well MB-06 but you will need to shave a little bit off the inner side of the pot metal o-ring.
To fit this unit properly you will need an 1. AEG barrel 2. AEG Hop bucking 3. nub and 4. the original pot metal O-Ring with hex screw to adjust lever (not shipped with this item).

v3 Owers will also need a new slimmer cylinder head (such as the ASPUK L96 Cylinder Head) as the the one supplied with your rifle is too thick.

For APS2 Type96 i.e. Fits Well, Warrior, Mauser, Maruzen L96 rifles . Will also fit M99.

It has the hole through centre for firing pin to pass through on some models.

Made from one steel block, CNC machined and case-hardened.

Suitable for both 7mm and 9mm springs.

Steel cylinder head. CNC Machined. Suitable for use with stock cylinders as well as our Steel cylinders.

You may receiver black or polished steel however they are identical.

Will fit Well, Warrior, Mauser, Maruzen models.

Steel durable cylinder is required in case of any upgrade. The stock cylinder is made of aluminium and is weak. It is easy to damage it with stronger upgrade spring. Our steel cylinder was sucessfully tested on the strongest springs.

Made of blackend coated Steel.

This model is suitable for Maruzen Type 96 and chinese copies such as MB-01 and MB-05. APS2 Type96 It is made on high precision CNC machines.

Not suitable for VSR or BAR 10! Weight 180g.

Tempered spring with blackening. This spring will provide approx 490-510 fps.

The FPS you get will differ depending on your setup and how good the rifles air seal is.

Spring is 9mm so will fit all upgraded pistons from manufactures such as PDI, Laylax or ASPUK. It will NOT fit the stock plasic piston.

Inner Barrel Spacer for Well MB-01,04,05,08 series or Maruzen APS. Made of durable polyacetal (POM) with two inner and two outer O-rings. Main purpose is to keep barrel in exact axle position. Installation doesn`t require any modification and is easy.

Two supplied.

This is a direct aluminium based replacement for the stock lever with slight modification of the prongs.

Please note: Picture shows blue hop lever installed in a hop unit.

14mm Anti Clockwise steel silencer adapter for the MB-01 & MB-05 L96 Type rifles i.e. Well, Warrior, Mauser & Maruzen.

Aero Chamber for the Maruzen APS type rifles. Requires standard AEG inner barrel.

Quick adjustment screws for the Maruzen Type96/ Warrior L96. this allows you to adjust the height of the cheek piece without using an allen key.

Laylax barrel spacers for the Maruzen type96 / Warrior/Well L96. These will hold the inner barrel steady which will increase accuracy.

Teflon coated cylinder for the Maruzen type96 / Warrior/Well L96. Decreases resistance, increasing consistency from shot to shot.

Laylax Zero Trigger for the Maruzen Typr96. Will also fit the Warrrior L96/G22. Has the strength to take high power upgrades.

Metal bearing spring guide for the L96. The addition of bearings on the guide allows the spring to turn, improving consistency.

Metal bearing spring guide for the Maruzen APS2. The addition of bearings on the guide allows the spring to turn, improving consistency. Will not fit the L96.

Laylax Thick 150SP spring for APS2/L96. This spring should achieve a velocity of approximately 480-500fps.
Requires high strength sears/trigger unit to operate.

Requires 9mm spring guide and PSS96 Piston.

Laylax Thick 170SP spring for APS2/L96. This spring should achieve a velocity of approximately 550fps. Requires high strength sears/trigger unit to operate.

Requires 9mm spring guide and PSS96 Piston.

These rubber pads are used to reduce noise from the piston hitting the cylinder head.

Fits APS2 Cylinder Head (P1007) and Cylinder Head (P1040).

These rubber pads are used to reduce noise from the piston hitting the cylinder head.

Fits Normal APS2 and Type 96 Cylinder Heads.

Silencer adapter for the L96. Will fit the Maruzen and Warrior versions. 14mm clockwise thread.

Harder piston head for the Type96. Will fit the Warrior L96/G22 and First Factory Type96 Piston.

High pressure piston for the APS2. Will also fit the Type96, Warrior L96/G22. Light weight for high performance.